SKnote Audio – SoundBrigade v3.7.6.0滤镜的具体配置和它们的交互方式使SoundBrigade成为一种新的独特效果 VST3 x64

音频效果器

SoundBrigade has an assigned “task” (algorithm). They act in response to an incoming signal, only in the frequency range assigned by the user. The specific configuration of the filters and the way they interact makes SoundBrigade a new and unique effect.

SoundBrigade有一个指定的“任务”（算法）。它们仅在用户指定的频率范围内响应输入信号而动作。滤镜的具体配置和它们的交互方式使SoundBrigade成为一种新的独特效果。


Tame – There is a frequency range in the track that stands out too much, but the equalizer is not an option. The action of filters tames its level, remaining transparent and maintaining dynamics.

Tame–赛道中有一个频率范围非常突出，但均衡器不是一个选项。滤镜的作用驯服了它的级别，保持透明并保持动态。


Control – In some tracks it may be necessary to get a fuller spectrum, not only by taming the peaks, but also by “upward” compression of the components.

控制——在某些轨道上，可能需要获得更充分的频谱，不仅要通过驯服峰值，还要通过“向上”压缩成分。


Wakeup – Used on boring tracks where the dynamics are too compressed or the spectrum is flat. Also interesting for experiments. High peaks get higher, low valleys get lower.

唤醒–用于动力学过于压缩或频谱平坦的钻孔轨道。实验也很有趣。高峰变高，低谷变低。


Rotate – No EQ action, no spectrum changes, only phase rotation. The more filters are focused on a narrow range, the stronger their effect. So-called “dispersion” (makes “tac” sound like “twack”), in a different sense. Try it on strong picks, as a de-esser, on pop, etc.

旋转–无EQ动作，无频谱变化，仅相位旋转。过滤器聚焦在窄范围内的次数越多，其效果就越强。所谓的“分散”（使“tac”听起来像“twack”），在不同的意义上。在强档，如德赛、流行音乐等上尝试一下。

Note: Only the Center and Range controls affect the “Rotate” mission.

注意：只有“中心”和“范围”控件会影响“旋转”任务。


Master – Like Tame, but the filter parameters have a strong frequency dependence, suitable for the mix.

Master–与Tame类似，但滤波器参数具有很强的频率依赖性，适合混合。


NEW in version 2 – Dry-out. Without thresholds, dries out the tails from the sound in the selected frequency range. Too much reverb somewhere? It can become magic.

版本2中的新功能–干燥。如果没有阈值，则会在选定的频率范围内使声音的尾部变干。某处混响太多？它可以变成魔法。


NEW in v.2 – De-snap. No threshold, tames peaks in the selected frequency range. Are some frequencies too dynamic? Install and work.

第2版新增功能–取消捕捉。无阈值，驯服所选频率范围内的峰值。有些频率太动态了吗？安装并工作。

NOTE: Some “Missions” use something similar to upstream compression. If you switch from one “Mission” to another, you can get a sharp increase in volume. Carefully manage your amplification system (headphones, speakers).

注意：有些“任务”使用类似于上游压缩的内容。如果你从一个“任务”切换到另一个，你可以得到一个巨大的增长。小心管理放大系统（耳机、扬声器）。


Threshold – Set the internal level threshold for filters. The actual value is linked to the Tilt control (see below).

阈值–设置筛选器的内部级别阈值。实际值与倾斜控制链接（见下文）。


Tilt – Music contains more energy in the low frequency range, less energy in the high frequency range. Looks like a slope of 4.5 to 6 dB/octave. The action of filters is smoother if their thresholds are aligned with the overall spectrum. This is NOT a sloped equalizer. For example, if Threshold is set to 0 dB and Tilt is set to 6 dB/octave, a filter centered at 100 Hz (one octave from the reference frequency, 50 Hz) has a threshold of -6 dB.

倾斜–音乐在低频范围内包含更多能量，在高频范围内包含更少能量。看起来斜率为4.5到6 dB/倍频程。如果滤波器的阈值与整个频谱一致，则滤波器的动作更平滑。这不是倾斜均衡器。例如，如果“阈值”设置为0 dB，“倾斜”设置为6 dB/倍频程，则以100 Hz为中心的滤波器（与参考频率相距一个倍频程，50 Hz）的阈值为-6 dB。


Makeup – a simple make-up enhancement after the effect.

化妆——效果后的简单化妆。

Switch Control / Snap – selection of the time constant for the effect. Snap is usually a bit slower, set to boost attack.

开关控制/捕捉–选择效果的时间常数。捕捉通常会稍微慢一点，设置为增强攻击。


Center – setting the center frequency for the operating range.

中心–设置工作范围的中心频率。


Range – setting the width of the action range. Outside this range, no effect is applied.
范围–设置动作范围的宽度。超出此范围，不应用任何效果。

Action – scales the overall action of the effect, from dry to maximum sensitivity.
动作–缩放效果的整体动作，从干燥到最大灵敏度。

Mission – filter operation algorithm.
任务–过滤操作算法。

Display – its mode changes depending on the selected mission. The bars show the input levels, the small squares show the action of the filters. There are no units of measure, the action is more complex, useful only as a visual guide.
显示–其模式根据所选任务而变化。条形图显示输入电平，小方块显示滤波器的动作。没有度量单位，动作更复杂，仅用作视觉指南。


Copy [folder] “SoundBrigade.vst3” to your VST3 directory.
将[文件夹]“SoundBright.vst3”复制到vst3目录。

游客，如果您要查看本帖隐藏内容请回复